Відео

Thanks for the awesome video, HUGE help getting the swap done!

Cool, what do u use for CAM generating g code,how good is it with detailed 3d parts. How fast can you push it Feed, thicknes cut per pass, tool, tool speed?

Harding Bisons logo?

Wanna be trd pros everywhere

What I just witnessed contradicts the reason we do breadboard ends. Glueing the entire edge does not allow the freedom for wood movement. If you are doing breadboard ends with a domino, you would glue the domino in the center on both ends, and the other domino's would only be glued on the panel side. You would not glue the entire edge of the panel. You would also do pins through the remaining domino's like you would any tenon on a breadboard. This method demonstrated I'm the video will probably be fine inside, but it would have problems in an area where moisture levels constantly change.

I just did the exact opposite I went from TRD Pro Grill to the Platinum Grill unfortunately cannot find camera bracket For the Platinum Grill any chance you still have that one you pulled off and are willing to sell it ???

Hey thanks for review how you like it now ?

Thank you for the video! I have the DeWalt DW618 but the 6 screws that came with the kit are too big and won’t fit to attach the base, what did you use?

That's dope

Where are your shoes

Another great video! I'm ready to go make a design and try cutting it out. Thank you.

EXCELLENT! Perfect pace with just the right amount of detail. I just got a 3018 to experiment with and your video was very helpful to get me started. I'll be subscribing and checking out your other videos. Thank you.

I need one of those. They look very sturdy

Nayahayayooo!! I will make you different!! *Zaps* Not metal… supposed to be buffalo.. I dont think so

Why is it venting into the garage?

Thanks man, big help

I farted.

Change to suction then put over something else.

I can't. Believe that you have an illegal discharge inside your garage.Hate to burst your bubble, but by law.You cannot have that discharging into your garage especially if it's a natural gas dryer.

thanks for sharing bud good instructions 😎

My sinuses hurt watching this

Dude, it had no choice but to work cause air going in one end of the pipe has only one other place to go and that is the other end unless the "other end" is seriously blocked.

Been doing this for years. But I don’t move the dryer. It’s easier to fashion a duct tape inlet into the dryer dust collector.

It didnt work. You only dislodged the loose lint there is still a lot trapped in there.

I can't believe the designers put the discharge in the garage.

I worked for a trapping service in the 90’.s. A common call was birds nesting in dryer vents. After pulling the nestin out with a hooked pole, we’d do this with leaf blowers. It’s not new, so I don’t understand the guy who uses a sewer cleaner to clean them. You’ll never get them 100% clean. A leaf blower gets 98%, I’d guess. So why go to all the effort of running a sewer snake through for 99%. Too much effort for too little gain. This guy in the video has the right idea.

Loose stuff coming out doesn't mean it worked. It can still be 90% clogged.. but you didn't show it really wotked. I wonder, why.

Why do you need this when you can just use the miter gauge?

Great vid, Ben! Loved seeing the CNC process from start to finish, including design, material setup, bit changes, and all the little details. Really helps me understand the whole picture! Can't afford a CNC like that for my own map-making, but dreaming about it!

But won’t moving it back into shop mess with the tram of the spindle to the waste board?

Great video. Now what size is the smallest fonts can you do?

Love a update with "long term" impressions of this set up please

That black chrome grill looked better. The plastic grille looks cheap

They need an in-chute EGO battery powered blade fan (like on leaf vacuumes that you pull behind your tractor) to increase suction down the chute and get all the grass/leaves into the bags. Mine clogs CONSTANTLY even with relatively dry Zorsia grass in my yard. The chute simply doesnt have enough air speed or volume to lift what most people are mowing.

I've been using a Monport laser recently, and it's been an incredible addition to my setup. Monport lasers offer excellent performance and are user-friendly, making them a fantastic alternative if you're considering expanding your laser capabilities. They're great for various materials, including metals, and the support from Monport

I love mine and the sled. I also use the TS/LS fence system

Should have painted it gloss black

Great job… looks awesome. I don’t see the link for the flat black plasti dip you used for the mustache? Can you comment the link pls?

Hi guys, I need the Bracket for the Camera but for the Platinum Grille, someone may have one I can buy from.

Looks great!

Last name Myer so i gotta comment and like. Also wish i could afford this stand right now. Almost got one second hand but someone beat me to it.

Kunthama paxa bro

This looks like a future project for sure. Looks great.

Blades on turbo would be a big help 😉

Boomer UA-cam is such trash. Do the thing in the title and stop burying the 3 minutes of content inside 30 minutes or trash no one wants to wade through to get to what they came to see. This entire trash video is "Drag the stl onto the canvas" and you dont even make the stl or do anything in the title. You're literally doing the same thing in every other vcarve video, except for what you put in the title. And all you throw is a link to some other jerk's website for how to actually do that. What a waste.

I have a Makita and 2 oem pullies do not fit shelix shaft and depth of keyway is not correct and key does not fit. I brought to attention during warranty and manufacturer will not fix.

MERCI ❤

01:14:39 <3

Yesss fisher

do you know if this grille would fit the 2024 tundra ?